Programa de Pós-graduação em Engenharia Civil
URI Permanente desta comunidade
Navegar
Navegando Programa de Pós-graduação em Engenharia Civil por Por Programa "Mestrado em Engenharia Civil"
Agora exibindo 1 - 20 de 37
Resultados por página
Opções de Ordenação
Item Análise experimental de vigas constituídas de perfis formados a frio com emendas soldadas submetidas à flexão simples(Universidade Federal de Goiás, 2009-09-23) ALMEIDA, Ariovaldo Fernandes de; GOMES, Orlando Ferreira; http://lattes.cnpq.br/3244852416821211The cold-formed steel sheets have been sufficiently used when it is thought of manufacturing a metallic structure with reduced weight. Its use until some time ago in construction was limited to the secondary structures, but, with considerable growth in research involving this type of material together with development of technical standards, made its use a good solution for certain types of light structures. The present work presents considerations on cold-formed steel sheets, the patened steel, processes of welding and the result of experimental tests with beams with composed section of two profiles U constituted with cold-formed steel sheets, manufactured with two types of patened steel produced in Brazil. In some of these beams, welded sections with coated electrode had been used and were made the comparison with the reference beam, where it was possible to study the influence of the process of welding in the ultimate resistance and the ductility of the beam.Item Levantamento das manifestações patológicas em fundações e estruturas nas edificações, com até dez anos de idade, executadas no estado de Goiás(Universidade Federal de Goiás, 2009-11-27) ALVES, Jader Rodrigues; GEYER, André Bortolacci; http://lattes.cnpq.br/0135796530510700The main objective of this research is to proceed to the rising of the indexes, to identify the pathologies and to characterize the constructions that presented occurrences of pathological manifestations in foundations and structures in the constructions executed in the State of Goiás, with age of up to ten years. The researches was classified as documental, considering that, to make possible the accomplishment of the same, the files of Regional Council of Engineering, Architecture and Agronomy of Goiás were analyzed -Crea/GO, with a total sample of 545 reports. It was observed that most of the processes are concerning the last seven years. This Organ was chosen by the fact that all of the technical documents are elaborated by professionals, and, mainly, for Official Organ to be considered. The Method of the Incidence was adopted as methodology recommended for this study observing that in the reports and decisions, elaborated by Crea-GO doesn't be in the number of occurrences of a same pathology and yes only the incidence of the same. The main conclusions of this research were: the main pathological manifestation was found in the foundations repression with a rate of 37.50% followed by collapse with a rate of 22.50%, both in relation to all the pathologies found in the foundation stage, the main pathological manifestation found in stage structure were the cracks with an index of 32.14% compared to all the pathologies found in stage design, regardless of the number executed and the second structural pathological manifestation found in step structure was the structural deformation with an index 19.84% as compared to all the pathologies found in stage design, regardless of the structural piece performed, the building of single-family residential use were the same who had diseases with a rate of 47.50%, followed by residential conference with 35 %, 77.50% of the buildings showed that diseases were carried out by private tutors and, for the buildings surveyed 40% had impairment evaluation of use of buildings facing the diseases occurred in moderate severity, and the rate for high severity was 5%. The disease occurred in low gravity, 45%, most pathological manifestations of both the foundation and structure, occurred in the first year of age of the building. 52.17% in the foundation and concrete structure in 40% of the buildings surveyed, 35% caused damage to neighboring buildings, and 53.49% of this damage occurred within the first year after completion of the work, and the buildings with an area of 5001 m² to 10,000 m² which caused the highest percentage of damage, and the recklessness and incompetence were more technical errors committed by professionals with rates of 32.50% each, followed by neglect of index 22.50 %.Item INFLUÊNCIA DE ADIÇÕES MINERAIS POZOLÂNICAS E DE FINOS DE PEDREIRA NAS PROPRIEDADES MECÂNICAS E NA MICROESTRUTURA DO CONCRETO AUTO-ADENSÁVEL(Universidade Federal de Goiás, 2007-08-27) ARAÚJO, Janaína das Graças; GEYER, André Bortolacci; http://lattes.cnpq.br/0135796530510700For the benefits of its properties in fresh state, self-compacting concrete (SCC) demands a high powder content in the composition, nearby 450kg/m³. The quarry dust, resultant material of the coarse aggregate production, can b considered as an economic and sustainable alternative for the development of the SCC. As well as the quarry dust, mineral additions, is used in conventional concretes and can also be used in the self-compacting concrete, with the same kind of benefits. Using the mix design for SCC developed by Tutikian (2004) a study for evaluation of the SCC mechanical properties were done, where natural sand had been partially replaced by quarry micaschist, granite and gneiss - and cement for silica fume, metakaolin and calcined clay pozolan. The test methods for fresh state used was Slump-flow (FURNAS, 2005a), U-Box (FURNAS, 2005b), Entrained air (NM 47, 2002) and Specific gravity (9833, 1997). Cylindrical test specimen 100x200 mm had been molded for tests - compressive strength (NBR 5739, 1994), modulus of elasticity (NBR 8522, 1984), splitting tensile strength (NBR 7222, 1994) and flexural strength (NBR 12142, 1991) -the age of 28 days. Samples using the mixture1: 4,5 had been analyzed by scanning electron microscope (SEM). The results show that it can be possible the use of different additions for the production of high quality SCC. We detach the small variability of the specific gravity, as well as the entrained air, wide presented low values. For concretes with same compressive strength, the values of modulus of elasticity had varied between 5 and 60% and the splitting tensile strength and flexural strength had been remained between 10 and 15%Item Influência do tipo de medição na determinação do módulo estático de elasticidade do concreto(Universidade Federal de Goiás, 2011-08-15) ARAÚJO, Suélio da Silva; GEYER, André Bortolacci; http://lattes.cnpq.br/0135796530510700; GUIMARÃES, Gilson N.; lattes.cnpq.br/0060821461126304The knowledge of the compressive strength and static modulus of elasticity is fundamental to the study of deformations of concrete, since deformations can cause cracks that compromise both the structural behavior of the element and serve as an entry to deleterious agents. For purposes of correlating values of compressive strength and static modulus of elasticity of concrete, cylinders were cast with different strengths, different types of strain measurements were taken, different specimen sizes and the loading speed of the testing machine. The specimens were tested at the age of 28 days to determine the compressive strength and static module of elasticity according to ABNT NBR 8522:2008, using different types of strain measurement devices: two mechanical dial indicators, surface bonded strain gages, clip gauges and LVDT (Linear Variable Differential Transducer). Two hundred and fifty eight specimens were cast with dimensions 150 mm x 300 mm and 100 mm x 200 mm using conventional normal strength concrete (NC - Class C30) and high strength concrete (HSC - Class C60). The experimental program was divided into two stages. First the static modulus of elasticity of concrete was measured to evaluate the accuracy of the method using different measuring devices and the accuracy of the method to a loading speed of 0.6 MPa/s. Then, the modulus of elasticity using different deformation measuring devices at a loading speed of 0.3 MPa/s and 0.6 MPa/s was measured. As for concrete NC and HSC, it was found that the specimens 100 mm x 200 mm obtained higher dispersion in relation to 150 mm x 300 mm specimens. In the first stage of the research, 100 mm x 200 mm specimens showed a higher dispersion when using mechanical dial gages and LVDT. The 150 mm x 300 mm NC class C30 specimens showed greater dispersion when using in mechanical dial gages and external strain gages. However, the HSC showed higher dispersion when mechanical dial gages and LVDT were used. In both concretes tested, the mechanical dial gages showed greater dispersion. In the second stage of the research, 150 mm x 300 mm specimens tested at the loading speed of 0.3 MPa/s showed greater dispersion when electrical strain gages and clip gauges were used. The 150 mm x 300 mm specimens tested at loading speed of 0.6 MPa/s showed greater dispersion when electrical strain gages and mechanical dial gages were used.Item Otimização de estruturas reticuladas planas com comportamento geometricamente não linear(Universidade Federal de Goiás, 2006-10-20) ASSIS, Lilian Pureza de; ALMEIDA, Sylvia Regina Mesquita de; http://lattes.cnpq.br/1855764480221018The aim of this work is to present a formulation and corresponding computational implementation for sizing optimization of plane frames and cable-stayed columns considering geometric non liner behavior. The structural analysis is based on the finite element method using the updated lagrangian approach for plane frame and cable elements, which are represented by plane truss elements. The non linear system is solved by the Newton-Raphson method coupled to load increment strategies such as the arch length method and the generalized displacement parameter method, which allow the algorithm to transpose any critical point that happen to appear along the equilibrium path. In the optimization process the design variables are the heights of the crosssection of the frame elements, the objective function represents the volume of the structure and the constraints impose limits to displacements and critical load. Lateral constraints impose limits to the design variables. The finite difference method is used in the sensitivity analysis of the displacement and critical load constraints. The optimization process is carried out using three different optimization strategies: the sequential quadratic programming algorithm; the interior points algorithm; and the branch and bound method. Some numerical experiments are carried out so as to test the analysis and the sensitivity strategies. Numerical experiments are presented to show the validity of the implementation presented in this dissertation.Item Análise não-linear de lajes de concreto armado pelo método dos elementos finitos(Universidade Federal de Goiás, 2006-09-27) BANDEIRA, Mirtes Silva; PRADO, Ademir Aparecido do; http://lattes.cnpq.br/4118518363912053In this work was carried simulations in the slabs and compared results with those obtained in the experimental research of Campos (2000) and Pires (2003), held on the slabs reinforced concrete brought to the failure by bending for inquiry of strengthening using uper the surface. For the modeling version 8.1.2 of DIANA was used and the inquiry of the behavior of the slabs was made through nonlinear analysis, adopting for the models elements of shell and solid. The behavior of the slabs was analyzed through the displacements central and approached the influence of the positioning of the reinforcement, the supports and the parameters that define the behavior of the concrete in the softening phase, being distinguished it maximum resistance of the concrete in the tension. The results are indicative of the good performance of the applied numerical models and that, the programs that use the concepts of the Fracture Mechanics in its formularizations, consist in powerful tool to reduce the amount of tests for the study of some specific phenomena, since that if they have resulted trustworthy of the behavior of the employed materials.Item GERENCIAMENTO DE PROJETOS PARA EDIFÍCIOS RESIDENCIAIS DE MÚLTIPLOS PAVIMENTOS: DIRETRIZES APROPRIADAS PARA COOPERATIVAS HABITACIONAIS AUTOGESTIONÁRIAS(Universidade Federal de Goiás, 2009-06-09) BARBOSA, Carlos Alberto de Jesus; FIGUEIREDO, Enio José Pazini; lattes.cnpq.br/4075543806767323Studies carried out by the United Nations (UN) show that a third of the population of the planet is suffering from the lack or inadequacy of dwellings and infra-basic structure. The deficit per dwelling is more serious in underdeveloped countries and developing countries, such as Brazil, and is becoming increasingly difficult to be solved without a great effort of the public, private initiative, financial institutions, education/research and associations on the basis of the various categories of work. As an alternative provision housing, has-if the participative management by mutual assistance, highlighting-if the housing cooperatives of auto-management. This program have presented high performance, where the works housing are being marketed and financed through this modality constructive, reducing the overall cost and increase the quality of the ventures. The mitigation of the overall cost of venture is a preponderant factor of success and survival of housing cooperatives of auto-management. The construction of residential buildings multiple floors enables the ventures housing cooperatives, because the high cost of developed land, usually with areas reduced, requiring increase the number of floors of the product for the better use of sites. The survival and servicing objectives of housing cooperatives of auto-management should consider four fundamental aspects: effectiveness in running (including the projects management), strong partnerships (with highlight to the public power, financial institutions , teaching/research, and other cooperative branches), existence of technical advice (from its constitution) and the target public (associated members with aware and motivated). Several studies identify that is in the projects management of the key to the reduction of waste of inputs and costs, with a gain in productivity and of the quality required to the final product. Considering the gaps in knowledge related to management of the project in the cooperative housing ventures, this study aims to investigate the main factors the quality of the production process, especially the stage of project of residential buildings with multiple floors built by the system of housing cooperatives of auto-management. As a result, the study provides some guidelines and tools for evaluating performance and quality of planning and control of the stage of project, from the studies of models, obtained by two aspects of phenomenological research. With the first vector seeks to at the literature national and international, models and tools for assessing the quality of project management, being more appropriate and would be appropriate for housing cooperatives of auto-management. Through the second vector investigated if, with the study of cases, two ventures of residential buildings multiple floors one in the city of Águas Claras DF, and another in the city of Goiânia GO, administered by housing cooperatives of auto-management. In these evaluated if the organizational structure, systems of an exchange of information, the weaknesses present and critical phases, planning and control the quality of the stage of project, the methodologies and tools of quality, in construction companies, design offices and between the intervening agents of the project process. It is concluded that the application management of the project in housing cooperatives of auto-management is a fundamental factor for survival,in implementing its main goal: to produce low cost housing and quality to their members.Item Influência dos Agregados Graúdos da Região de Goiânia no Módulo de Deformação Tangente Inicial do Concreto(Universidade Federal de Goiás, 2009-11-24) BARBOSA, Isa Lorena Silva; GEYER, André Bortolacci; http://lattes.cnpq.br/0135796530510700This research is carried out to study the influence of aggregate source on the initial tangent modulus of deformation of concrete (Eci), to correlate the resistance to compression (fc) with the module Eci and compare the results of this research with the equations proposed by international standards and the Brazilian. To this end, it was used three levels of resistance to 28 days: 20MPa, 30Mpa and 40Mpa and ranged up the aggregate source in the types lithological micaschist, Granulito and Basalt. Set the type of cement, sand, water, and additive content of mortar. All materials are used in dosages of Goiânia and the surrounding region in order to determine the behavior of these materials in concrete that is produced in the region. The experimental program of this research is divided into two parts. The first is to determine the curves of strength of each aggregate source test of resistance to compression in the age of three, seven and 28 days, while the second part determines the initial tangent modulus of deformation on the ages of seven and 28 days. For the first part of the experimental program were molded 54 body-of-evidence and tested for resistance to compression. For the second part was molded 90 body-of-evidence, where 36 were tested for resistance to compression and 54 with the initial tangent modulus of deformation. With the end of testing was performed a statistical analysis of results obtained through software STATISTIC. In the analysis it was the influence of aggregate source in the initial tangent modulus of deformation (Eci), noting influences the levels of resistance adopted and distinct variations in the influence of aggregate source studied on the Eci, by increasing order of the results of module: micaschist, granulito and basalt. The results also indicated that the NBR 6118 (ABNT, 2003) overestimates the values of modulus of deformation of concrete.Item Influência do tipo e do tempo de duração de cura nas propriedades mecânicas de concretos de alto desempenho (CAD) produzidos em períodos quente (t>25°C) e de baixa umidade relativa do ar (h<50%)(Universidade Federal de Goiás, 2005-06-07) BESERRA, Simone Ataíde; BACARJI, Edgar; http://lattes.cnpq.br/2385473000869120; GEYER, André Bortolacci; http://lattes.cnpq.br/0135796530510700In the case of conventional concrete, small constructive defects, variations of mix proportion or even inadequate curings can not compromise significantly the material. No longer HPC demands a severity in the control since its dosage until the execution, therefore any imperfection can bring serious damages to the material or the structure. Amongst the relative aspects most important to the total quality of any concrete it is the curing, that becomes basic when is about HPC. The curing of the high performance concrete constitutes in a controversial subject in the technician area as well as the type and duration of it, therefore the necessity of a deeper refined study on this subject. This research verifies the influence of the type and time of duration of curing in the mechanical properties of the HPC (compressive strength, flexion tensile strength and module of deformation), produced in Goiânia in hot period (t>25ºC) and of low relative humidity of air (h<50%) situation this considered critical for NBR 14931/2003 and predominant in the months of May the September in this region. In the experimental study were produced HPC of target compressive strength 60, 80 and 100MPa, from the Furnas Mix Proportion Method, using cement CP II-F-32, silica fume, polycarboxylate based superplasticizer, natural sand and crushed stones nº 0 of the granulite. 14 cures of different type and times of duration had been applied: curing with permanence of 1, 3, 7, 14, and 28 days inside of the humid chamber; curing with aspersion of water during 1, 3, 7, 14 and 28 days; chemical curing based on paraffin and chemical curing based on chloride rubber; cure for aspersion of water during 7 days and later sealing of the part with membrane of curing based on chloride rubber and air curing. For concretes of target compressive strength to the 28 days of 60 MPa and 80 MPa, the best type of curing was "saw humid" (curing in humid chamber and curing with aspersion of water) and the best time of duration humid was 7 days. For the one of 100 MPa the best type of curing also was "saw humid", however the duration time was 14 days. According to the chemical curing, some times the results had been even though less than to the one of reference (air curing). Among the two types of used chemical curing, difference in the results of compressive strength was not verified, despite the chemical membrane based on paraffin has an inferior cost to the chloride rubber base.Item Avaliação da qualidade de concretos produzidos em centrais dosadoras, misturados em caminhão betoneira e de concretos produzidos em centrais misturadoras(Universidade Federal de Goiás, 2009-12-14) BORGES, Michelly Lorena; GEYER, André Bortolacci; http://lattes.cnpq.br/0135796530510700Due to the small number of studies about the process of production of the concrete dosed in central, as regards the type of employed mixture, this inquiry looked to contribute to the assessment of quality of concrete produced in mixing plant and metering plant. The principal objective of the work was checking if the form of mixing of the concrete can affect your characteristics in hardened state (compressive strength), for that, there was compared the quality of the concrete produced in metering plant and mixed in truck mixer in relation to the mixing plant. As the sample was taken a work, where they had installed a metering plant and a mixing plant, which together produced 300.000 m³ of concrete with the same materials. Inside the proposed objective, also were quantified statistically the existent types of concrete in the same truck mixer, using as the parameter the compressive strength of concrete produced in the metering plant. In the end, it was possible to conclude that the mixing plant produce a concrete of better quality with a less standard deviation than the metering plant. Was also observed a significant variability inside the truck mixer, which made the division of the concrete possible in five group, with different resistances'Item Influência da areia artificial oriunda da britagem de rocha granito-gnaisse nas propriedades do concreto convencional no estado fresco e endurecido(Universidade Federal de Goiás, 2007-10-31) CABRAL, Keillon Oliveira; FIGUEIREDO, Enio José Pazini; lattes.cnpq.br/4075543806767323The dissertation is aimed at the study being presented theoretical and experimental verification of the performance of artificial sand come from crushing the rock of granite-gneiss in relation to natural sand. Currently, the sand has artificially low commercial value of the market and is considered a "some kind of piece of marginal material ", whose purpose is not defined and remained stored in the courtyards of the quarries, forming huge piles that cause various environmental impacts. In addition to this, the traditionalism and the lack of information has led to an unwarranted mystification of this material. The methodology used for the tests of the research was based on standardized tests, which attempt to meet the objectives of the dissertation, in addition to enhancing the development of techniques to search for alternative aggregates. This has examined the influence of artificial sand in place of natural sand, with different proportions, and focuses on quality of the concrete in plastic and hardened its phases, taking into account the mechanical, elastic, physicalchemical, environmental and economic. The work was to characterize the material that composed the concrete studied. After this phase, were up corpses-of-proof concrete, using 15 (fifteen) different traits, so that the natural sand was gradually replaced by artificial sand, in proportions of 25%, 50%, 75%, and 100%. For each trait was quantified its rebate, density, air incorporation, resistance to axial compression, traction, deformation module, absorption by immersion, alkali-aggregate reaction and an economic evaluation. It is considered that the main objective of this research has been fully achieved, because it was proven the theoretical feasibility of replacing part or even all, of natural sand by artificial sand in conventionalItem Cadastro Geotécnico dos solos finos lateríticos para fins de pavimentação no município de Goiânia- GO(Universidade Federal de Goiás, 2010-08-24) CARDOSO, Ricardo Alves; ROMÃO, Patrícia de Araújo; http://lattes.cnpq.br/0188184635964559; REZENDE, Lilian Ribeiro de; http://lattes.cnpq.br/9258692609398794This work aims at the register of geotechnical areas in Goiania-GO, showing the occurrence of fine lateritic soils with potential for use in flooring. The methodology is based on work developed by Nogami and Villibor (1995). From surveys and collecting 17 samples in field tests were conducted from MCT (Mini-MCV, Loss of mass by immersion, compression and Mini-CBR) and verified the mechanical and hydraulic properties of these soils. The samples were collected at sites previously chosen using as reference the pedological map of Goiania, trying to distribute them to all soil units of this map. The surveys were performed to a depth of 2 m in each hole the soils were mixed, representing what occurs in practice during the operation of a loan area. The samples collected for the study were those who had only fine soil grains with diameters of less than 2 mm (sieve nº. 10). Tests were also carried out conventional characterization (particle size, Atterberg limits and specific gravity) of the samples collected to better identify these soils. The results obtained with all samples have the intention to form a database for future research in the area of pavement. It was found that in Goiania most soils are lateritic clay and can be applied in the construction of paviments with low traffic volume.Item CONTRIBUIÇÃO AO ESTUDO DAS PROPRIEDADES MECÂNICAS E DA DURABILIDADE DE CONCRETOS COM ESCÓRIA DE ACIARIA ELÉTRICA (EAF) COMO AGREGADO GRAÚDO(Universidade Federal de Goiás, 2007-10-17) FARIA, Ricardo Andrade Fernandes; TUBINO, Rejane Maria Candiota; http://lattes.cnpq.br/5775852172717383The increasing demand for aggregate for uses in engineering stimulated the search for alternative materials. In this way, the civil construction potentially started to be a great consumer of residues from other industries, becoming a great recycle plant. The use of by-product, brings great environmental benefits in relation to the degradation of the environment, as for example, less settlement of residues in earth fill, the reduction of extraction of natural resources, and the exploration of aggregate ores. Steel plants from around the world have a commom problem, that is what to do with all the steel slags generated as a by-product from the steel refining in electric steel plants or oxygen steel plants. There are two points of these process where slags can be generated: the first comes from the electric or oxygen furnace itself (called oxidizing refining) and the second is the laddle metallurgy slag (reduction refining slag), which is the last stage of the steel production. This aims to demonstrate related studies to the use of steel slags (EAF slags) in electric steel plants as coarse aggregate. Expansibility of the steel slag tests had been carried through, compressive strength, tensile strength for diametrical compression, related modulus of deformation and durability tests, such as: intensity of corrosion, potential of corrosion, ohmic resistivity and depth of carbonation. After this, it was observed the similarity of the results between the concrete made with steel slag and the concrete made with conventional aggregates, natural aggregate known as mica schist. It was observed improvements in the properties of the concrete with steel slag, such as: increase in its strength (compressive / tensile) and increase of the modulus of deformation. Concerning the durability, it was noted, in a general way, that the substitution of the aggregates, conventional for siderurgical, has not influenced in the performance of the concrete.Item Critérios normativos sobre influência da relação Aw/Af e esbeltez de alma no cálculo da resitência à flexão de vigas esbeltas em elementos de estruturas de aço.(Universidade Federal de Goiás, 2007-10-01) FERNANDES, Rodrigo; BACARJI, Edgar; http://lattes.cnpq.br/2385473000869120; GOMES, Orlando Ferreira; http://lattes.cnpq.br/3244852416821211This work contains a theoretical analysis of the behavior of plate girders. A plate girder has been calculated based on the criteria of the American standard Manual of Steel Construction Load and Resistance Factor Design (AISC, 1994), and checked by the Brazilian standard NBR 8800: Projeto e execução de estruturas de aço de edifícios (método dos estados limites) (ABNT, 1986), the revision project of the Brazilian standard Projeto de Revisão da NBR 8800: Projeto e execução de estruturas de aço e de estruturas mistas aço-concreto de edifícios (ABNT, 2003), the revision project of the Brazilian standard Projeto de Revisão da NBR 8800: Projeto de estruturas de aço e de estruturas mistas de aço e concreto de edifícios (ABNT, 2007) and the European standard Eurocode 3: Design of steel structures Part 1.1: General rules and rules for buildings (CEN, 1992). PFEIL (1989) has calculated a plate girder by using the Brazilian standard NBR 8800/86. The calculated dimension have been checked by the mentioned standards. NARAYANAN (1992 apud OWENS, KNOWLES E DOWLING, 1992) has dimensioned a plate girder by using the British standard BS 5950: Structural use of steelwork in building. Part 1: Code of practice for design in simple and continuous construction: hot rolled sections (BSI, 1990), which has also been checked by the mentioned standards. Furthermore, theoretical analyses related to the calculus of plate girders presented by many authors have been considered. The main goal is to assess the criteria utilized by the standards for the calculus of plate girders. From the obtained results, for the checked girders, by the standards and related theories, a comparative analysis among the utilized criteria by the standards has been made. The reached conclusion is that the Brazilian standard and its revision projects has identical criteria compared to the American standard for the calculus of plate girders. The European standard presents slightly different criteria compared to the American standard; however, both provide close results one compared to another. The theories utilized have also provided close results from those obtained by the standards.Item Resistência à tração de pinos de ancoragem isolados e pré-instalados : Influência da armadura de flexão e de cisalhamento(Universidade Federal de Goiás, 2011-06-27) FONTENELLE, Emmele Gonella; GUIMARÃES, Gilson N.; lattes.cnpq.br/0060821461126304; GOMES, Ronaldo Barros; lattes.cnpq.br/6046088082653028Fastenings inserted in concrete are used in order to allow the introduction of these components in concrete structures, enabling the structural link between metal structures and concrete foundation and between prefabricated components and fixing reinforcement elements. This work will study specifically an anchoring system pre-installed (cast-in-place anchor), consisting of single head studs with square head and subjected to tensile force. Assays were performed in 30 headed studs, using self-compacting concrete with compressive strength in the C-30 class. The main variables are the presence and rate of reinforcement, the arrangement of reinforcement in the blocks, and the influence of both the flexural reinforcement (longitudinal and transverse) and the shear reinforcement (hairpins) on the load capacity of the anchorage. The experimental results were compared with five methods of design found in the literature and show that the flexural einforcement has no effect in increasing the load capacity of the anchorage. The use of a shear reinforcement together with the flexural reinforcement can increase the capacity of the anchor up to 64%. Increasing the distance of the hairpins in relation to the head stud reduces the ultimate load achieved by the anchoring system while the increase in diameter and / or in the number of layers of hairpins can increase the ultimate load.Item INFLUÊNCIA DO TAMANHO DO CORPO DE PROVA NOS RESULTADOS DE ENSAIOS DE MÓDULO DE DEFORMAÇÃO E RESISTÊNCIA À COMPRESSÃO E SUAS CORRELAÇÕES PARA CONCRETOS PRODUZIDOS EM GOIÂNIA - GO(Universidade Federal de Goiás, 2008-10-03) MARTINS, Danilo Gomes; GEYER, André Bortolacci; http://lattes.cnpq.br/0135796530510700Even though the different sizes of cylindrical specimens for tests in concrete are standardized to get the simple compressive strength and the modulus of elasticity, this factor is not usually studied in most researches. So, the goal of this thesis was to evaluate the influence of the size of the specimens in the initial tangent modulus of elasticity (Eci) and in the compressive strength (fc), correlate the values of fc and Eci, and compare the values of modulus of elasticity that were estimated by the equations proposed by the Brazilian code (NBR 6118/2003) and by the American norm (ACI 318/2002). Concretes with three levels of strength were used after 28 days: 25MPa, 30MPa and 40MPa. They were all proportionally mixed with materials of the region and supplied by only one concrete batching plant of Goiânia GO. The tests of compressive strength and initial tangent modulus of elasticity were done in cylindrical specimens of 100 x 200 mm and 150 x 300 mm after 28 days. The samples were collected during the delivery of the concrete in the construction sites. For each truck, ten specimens were molded, five of 100 x 200 mm and five of 150 x 300 mm. Of the 600 specimens that were molded, 240 tests of compressive strength and 360 tests of modulus of elasticity were done. The cure was in a tank with water saturated with limestone. After the tests were done, the statistical analysis of the results was done. The variance analysis (ANOVA) indicated that the size of the specimen exerts influence only on the results of the initial tangent modulus of elasticity (Eci). There is a tendency for the specimens of 100 x 200 mm to show greater results for the modulus of elasticity of the concrete than the specimens of 150 x 300 mm. In the compressive strength, only the level of strength significantly exerted influence on the results. It was also observed that the NBR 6118/2003 overestimates the values of modulus of elasticity of the researched concretes and the results are better adequate to the model proposed by the ACI 318/02.Item Estrutura mista madeira-chapa dobrada submetida à flexão simples(Universidade Federal de Goiás, 2007-09-28) MONTEIRO, Vilma França; GOMES, Orlando Ferreira; http://lattes.cnpq.br/3244852416821211; BACARJI, Edgar; http://lattes.cnpq.br/2385473000869120This work deals with theoretical and experimental study of timber beams and timber/cold formed steel plates composed beams, submitted to the bending. A combination of different materials aims to the exploitation the advantages of each material, of manner to have a viable set, in constructive terms, structural and economic. For the accomplish of the research, three beams wooden with dimensions 40mm x 120mm x 1050mm, six hardened beams wooden in the superior face with metallic profile in the dimensions 50mm x 25mm x 2mm and six beams of wooden stiffeners in faces inferior and superior with the same profile metallic had been assayed. The spacing between the connectors had been of 100mm, 200mm and 300mm. With the objective to supply given necessary the sizing, a theoretical formularization for the determination of the internal moment and for the estimative of the deflection was presented. For this, the mechanical properties of the wood, the steel and the connectors had been determined. With the results of the assays of characterization of the materials, the simple and mixing beams had been assayed to the bending, for reading of the deformations and maximum vertical displacements of the landslide in the extremities inferior and superior. Such values had been gotten by means of electric strain gauges and comparing clocks. They had been determined still: the tensions in the elements of the beams and the curves load versus displacement. It was observed that, in relation to the wooden simple beam, it had average increase at the ultimate load, for the beams with parts hardened in the compressed face, of 20%, and of 49 when placed stiffeners in the faces compressed and tensioned. In the value of the deflections it had average reduction of 15% when used stiffener in the superior face and of 49% in the parts with stiffeners in the faces was used compressed and tension. The biggest reduction in the deflections happened in the parts with lesser spacing between connectors, indicating that the influence of the interaction is bigger in relation to the displacements that in relation to the bending moment. In stress distribution diagram in the transversal sections it was adopted, in all the cases, the triangular form for the wood and for the profile it was adopted a rectangular form. It was obtained results that differ from the experimental values in 17% for the simple beams, in 16% for the parts hardened with profile in superior face and 21% for the parts hardened with profile in the faces upper/lower indicating that the formularization proposal can be applied with safety. In the calculation of the deflections the geometric properties of the mixing section, in elastic regimen, had been gotten with the homogenized section. An equation for the determination ofthe factor of correction of the estimated deflection, for the studied cases is presented.Item Punção em lajes cogumelo : estudo da retangularidade dos pilares(Universidade Federal de Goiás, 2006-08-31) MOURO, Valéria Conceição; GUIMARÃES, Gilson N.; lattes.cnpq.br/0060821461126304; GOMES, Ronaldo Barros; lattes.cnpq.br/6046088082653028Eight reinforced concrete square flat slabs of reinforced concrete were tested. Slabs were 130mm thick with an 1800 mm side and were submitted to central loading, and the objective was to investigate the influence of column rectangularity coefficient. Column cross section dimensions (cmáx/cmín) varyied between 1 and 4, with a constant perimeter equal to 1000mm. Results presented and analysed include ultimate loads and failure types, modes of rupture, vertical displacements, cracking and deformations of steel and concrete. Comparisons with codes, norms and results of literature results are also presented. The results indicate that as the rectangularity coefficient increases, punching shear resistance decreases for constant perimeter column flat slabs. Suggesting that punching shear has to be considered specially in regions close to column extremity, where there is a larger concentration of shear forces. A proposal for an inclusion of the retangularity parameter (cmáx/cmín) in expressions for calculation punching shear resistance of ACI (2002), CEB-FIP (1991), EC2 (2001) and NBR-6118 (2003) codes is presented.Item Análise experimental de pilares de concreto armado submetidos à flexo-compressão, reforçados com concreto auto-adensável e conectores(Universidade Federal de Goiás, 2009-09-11) NASCIMENTO, Poliana Paula; GOMES, Ronaldo Barros; lattes.cnpq.br/6046088082653028Many problems involving cases of ruins of buildings, bridges, etc., specifically ruin of columns, which are among the most important links in the whole structure, due to project flaw, bad execution or even for the evolution and changing habits. Therefore it has been of fundamental importance researches on the experimental behavior of structures. When conducting a strengthening column using dry with increased self-compacting concrete, it has the drawback of a sudden rupture by peeling the reinforcement. For this, there is a need to study the area of adhesion between substrate and to strengthen and create a way of preparation of this interface area so that the column increases may come into ruin in a ductile flexural as well as in a monolithic column. Thus, it s been developed an experimental study in the School of Civil Engineering, Federal University of Goias, based on analysis of the breaking loads, lateral displacements and deformations of the column of materials for different ways of preparing the surface of the column to be strengthened. The experimental phase of this work was based on testing of nine reinforced concrete columns, which are tested under flexural compression, with eccentricity of 60 mm. Two columns were used as reference columns, one with the original dimensions of the column and the other monolithic concreted in the thickness of a sin reinforced the others received a layer of 35 mm thick concrete selfcompacting in the compressed face. For preparation of the interchange between the two materials, it was proceeded with the scarification and the realization of grooves along this surface, where inserted connectors attached to transverse reinforcement of the columns, varying the position and quantity of the same. It can be concluded that not only quantity, but mainly the location of connectors used in the connection between the substrate and reinforcement, is essential for a good result of resistance and rupture mode. Must be observed a minimum spacing between the connectors strengthening to ensure a more monolithic unit, enabling a ductile rupture occurred as the reference columnItem Influência do agregado graúdo reciclado de resíduos da construção predial nas propriedades do concreto fresco e endurecido(Universidade Federal de Goiás, 2007-10-04) NUNES, Wesley Carlos; FIGUEIREDO, Enio José Pazini; lattes.cnpq.br/4075543806767323Recycling waste materials is an efficient way to hinder environmental, social and economic impacts of the civil construction industry. This dissertation aimed at verifying the behavior of different concretes made of coarse recycled aggregate (AGR), mineral fractions collected from the waste (RCD) of a high- rise apartment building (multiple floor building). The RCD has been selectively collected at the building construction site and processed by a jaw crusher. The study focused on the effects of gradual replacements of coarse natural aggregate (AGN) by AGR where the fundamental properties of the fresh and hardened concretes are concerned. The experiment involved the production of three dry aggregate/ceme nt ratios: (3,5 / 1), (5 / 1) and (6,5 / 1) for each concrete family (zero%, 25%, 50%, 75% and 100% replacement contents of AGN by AGR), and thus 15 different concrete mix proportions were manufactured. Workability, entrapped air, and density were the variables analyzed in the fresh concretes. Furthermore, water absorption, density, total pores volume, compressive strength, splitting-tensile strength, and initial-tangent modulus were the properties studied in hardened concretes. The strengths of concretes with AGR contents are lower than those of corresponding reference concretes (zero% of replacement content of AGN by AGR). However, reductions in the cement content in mixtures of the concretes produced with AGR showed compressive and splitting-tensile strengths values nearer to those of the reference concrete family. The experiment allows for the conclusion that concretes produced from AGR of RCD can be used for several purposes in civil construction, if the management of concrete mix proportions and the control of quality are performed under the liability of capable and qualified professionals.